All categories

Attwood 2-Way On/Off Bilge Pump Switch

0

2-Way On/Off Bilge Pump SwitchPart #: 7615-3Panel-mounted rocer switches for use with pump that draws 10 amps or less.Features:1/4" spade terminals6-volt through 32-volt D.C. only10 amps maximumPlate is 2-13/16" x 1-7/8"Hole size is 1-1/2" x 7/8"Caution:Bilge pump switches are not external ignition ..

$22.99

Attwood 3-Way Auto/Off/Manual Bilge Pump Switch

0

3-Way Auto/Off/Manual Bilge Pump SwitchPart #: 7615A3Panel-mounted rocker switches for use with pump that draws 10 amps or less. Features:1/4" spade terminals6-volt through 32-volt D.C. only10 amps maximumPlate is 2-13/16" x 1-7/8"Hole size is 1-1/2" x 7/8"Caution: Bilge pump switches are not extern..

$22.99

Attwood Automatic Float Switch - 12V & 24V

0

Float SwitchPart #: 4202-7Converts bilge pumps to fully automatic operation. Maximum amp draw is 12 amps (at 12-volt D.C.) or 6-amps (at 24-Volts D.C.). Features a compact, low profile design that mounts on any surface from a horizontal up to a 24x angle. Incorporates a reliable and affordable mecha..

$29.99

Attwood Automatic Float Switch w/Cover - 12V & 24V

0

Float Switch w/CoverPart #: 4201-7Converts bilge pumps to fully automatic operation. Maximum amp draw is 12 amps (at 12-volt D.C.) or 6-amps (at 24-Volts D.C.). Features a compact, low profile design that mounts on any surface from a horizontal up to a 24" angle. Incorporates a reliable and affordab..

$29.99

Attwood Bilge Pump Installation Kit w/Switch, 3/4 Hose Clamps & 20' Wire Fuse Holder

0

Bilge Pump Installation KitPart #: 4116-5Complete kit to install manual bilge pump with 3/4" or 1-1/8" I.D. hose outlet.Features:(1) 2-way on/off switch with bezel plate(1) 3/4" I.D. x 5' corrugated hose(1) Thru-hull fitting for 3/4" I.D. hose(2) Snap-It hose clamps(2) 2-conductor 16-gauge wire, 20'..

$42.99

Attwood Bilge Switch S3 Series - 12V

0

Automatic Bilge Switch S3 SeriesPart #: 4801-7Incorporates a proprietary Electronic Sensing technology to detect bilge water levels and trigger pump activation and has been engineered to operate in any bilge water mixture consistently without failure. Your pump won't be exposed to continuous cycling..

$37.99

Attwood Heavy-Duty Bilge Pump 1700 Series - 12V - 1700 GPH

0

Heavy-Duty Bilge Pump 1700 SeriesPart #: 4730-4Heavy-Duty Bilge Pumps integrate the highest quality bearings, brushes, alloys and magnets designed to withstand extreme usage cycles. Pump all employs an exclusive shaft and motor compartment, reducing wear and significantly extending pump life. Advanc..

$113.99

Attwood Heavy-Duty Bilge Pump 2000 Series - 12V - 2000 GPH

0

Heavy-Duty Bilge Pump 2000 SeriesPart #: 4760-4Heavy-Duty Blige Pumps integrate the highest quality bearings, brushes, alloys and magnets designed to withstand extreme usage cycles. Pump all employs an exclusive shaft and motor compartment, reducing wear and significantly extending pump life. Advanc..

$126.99

Attwood Sahara Automatic Bilge Pump S500 Series - 12V - 500 GPH

0

Sahara Automatic Bilge Pump S500 SeriesPart #: 4505-7An automatic-switch bilge pump is a requirement for any vessels 20' and over with sleeping accommodations, but is a great convenience for any size boat. The Sahara has everything contained in one compact yet durable package - pump, wire, seals, st..

$58.99

Attwood Sahara Automatic Bilge Pump S750 Series - 12V - 750 GPH

0

Sahara Automatic Bilge Pump S750 SeriesPart #: 4507-7An automatic-switch bilge pump is a requirement for any vessels 20' and over with sleeping accommodations, but is a great convenience for any size boat. The Sahara has everything contained in one compact yet durable package - pump, wire seals, str..

$89.99

Attwood Shower Sump Pump System - 12V - 500 GPH

0

Shower Sump Pump System - 500 GPHPart #: 4141-4Attwood's shower sump systems deliver the performance you've been asking for. Standard Box size that offers fast water flow into and out of sump. The lid snaps in to allow quick installation (and removal for cleaning) and includes a gasket to seal the s..

$127.99

Attwood Shower Sump Pump System - 12V - 750 GPH

0

Shower Sump Pump System - 750 GPHPart #: 4143-4Attwood's shower sump systems deliver the performance you've been asking for. Large Box size that offers fast water flow into and out of sump. The lid snaps in to allow quick installation (and removal for cleaning) and includes a gasket to seal the sump..

$134.99

Attwood Tsunami Bilge Pump T1200 - 12V - 1100 GPH

0

Tsunami Bilge Pump T1200Part #: 4612-7With their innovative engineering and compact design, Tsunami pumps deliver high output from a small package. We use the advanced material available, including the best quality bearings and state-of-the-art brushes, alloys and magnets. Our patented shaft seal pr..

$44.99

Attwood Tsunami Bilge Pump T500 - 12V - 500 GPH

0

Tsunami Bilge Pump T500Part #: 4606-7With their innovative engineering and compact design, Tsunami pumps deliver high output from a small package. We use the advanced material available, including the best quality bearings and state-of-the-art brushes, alloys and magnets. Our patented shaft seal pre..

$26.99

Attwood Tsunami Cartridge Motor - Replacement f/T1200

0

Tsunami Cartridge Motor - Replacement f/T1200Part #: 4624-6This replacement cartridge motor fits the T1200 Tsunami Bilge Pump and Aerator Pump. Product : ATTWOOD TSUNAMI REPLACEMENT MOTOR CARTRIDGE F/ T1200 Manufacturer : ATTWOOD MARINE Manufacturer Part No : 4624-6 UPC : 022697462435..

$37.99

Attwood Tsunami Cartridge Motor - Replacement f/T500

0

Tsunami Cartridge Motor - Replacement f/T500Part #: 4620-6This replacement cartridge motor fits the T500 Tsunami Bilge Pump and Aerator Pump. Product : ATTWOOD TSUNAMI REPLACEMENT MOTOR CARTRIDGE F/ T500 Manufacturer : ATTWOOD MARINE Manufacturer Part No : 4620-6 UPC : 022697462039..

$18.99

Attwood Tsunami Cartridge Motor - Replacement f/T800

0

Tsunami Cartridge Motor - Replacement f/T800Part #: 4622-6This replacement cartridge motor fits the T800 Tsunami Bilge Pump and Aerator Pump. Product : ATTWOOD TSUNAMI REPLACEMENT MOTOR CARTRIDGE F/ T800 Manufacturer : ATTWOOD MARINE Manufacturer Part No : 4622-6 UPC : 022697462237..

$28.99

Attwood Tsunami T800 Bilge Pump - 12V - 760 GPH

0

Tsunami T800 GPH Bilge PumpPart #: 4608-7With their innovative engineering and compact design, Tsunami pumps deliver high output from a small package. We use the advanced material available, including the best quality bearings and state-of-the-art brushes, alloys and magnets. Our patented shaft seal..

$33.99

Beckson Canoe & Kayak Pump - 18L, 8GPM

0

Canoe/Kayak PumpFeatures:Diameter: 1-3/4" Length: 18" Strokes per Gallon: 8 strokes Gallon per minute: 8 gallons Mounting clips sold separately Product : BECKSON CANOE & KAYAK PUMP 18" LENGTH 8 GPM Manufacturer : BECKSON MARINE Manufacturer Part No : 318P UPC : 021083000190..

$32.90

Beckson Diaphragm Pump - 16GPM

0

Diaphragm PumpMade of corrosion-proof marine plastic. Two position stainless steel handle and adjustable (Octagonal) frame permits up to 16 variations in stroke direction. Mounts vertically on bulkhead or horizontally on deck without the need for special brackets. Uses Beckson FH-1-1/2 or VCS-1-1/2..

$149.00

Beckson Flex-a-Pump Impossible Place Pump w/6' Intake

0

Flex-a-Pump Impossible Place PumpsA Thirsty-Mate with extra reach! This pump can be permanently installed and will operate in any position. It comes complete with mounting brackets, intake hose and clamp, strainer, check valve and discharge hose. Ideal for small boats, engine compartments and much m..

$89.00

Beckson Float-a-Pump Sleeve f/124, 136 & 300 Series Pumps

0

Float-a-Pump Flotation SleeveAdd a Float-A-Pump Sleeve (FPS-3R) to provide positive flotation in case the pump slips overboard. This bright red sleeve slides over the foot onto the pump body, providing high visibility as well as flotation. Fits 124, 136 and 300 series pumps. Product : BECKSON FLOAT..

$10.55

Beckson Rock Strainer f/124, 136 & 300 Series Pumps

0

"Off the Boat" Rock StrainerThis strainer replaces the existing foot on the pump and prevents small rocks from damaging the foot valve. Fits 124, 136 and 300 series pumps. Product : BECKSON ROCK STRAINER F/ 124 & 136 & 300 SERIES PUMPS Manufacturer : BECKSON MARINE Manufacturer Part No : FVR1-3/4 ..

$20.45

Beckson Sea Kayak Pump - 18L, 8GPM w/Float-a-Pump

0

Sea Kayak Pump w/Float-a-Pump SleeveDesigned specifically with the Sea-Kayaker in mind, this upgraded version of our popular Canoe Pump includes an aluminum reinforcing shaft which prevents the pump shaft from flexing in a rolling sea and won't affect a compass. A hose can be added for extended disc..

$52.35

Beckson Siphon-Mate Pump f/Diesel, Oil, Water

0

Siphon-Mate Siphon PumpSpecialty Transfer PumpSafety experts caution against the unsafe practice of siphoning petroleum by mouth, warning specially, that it can result in loss of life. Beckson's answer is the patented Siphon-Mate pump; a combination displacement lift pump and siphon pump with valves..

$48.85

Beckson Thirsty Mate Pump 24 w/24 Flexible Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$37.80

Beckson Thirsty-Mate 24 Pump w/24 Flexible Reinforced Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$41.60

Beckson Thirsty-Mate 24 Pump w/72 Flexible Reinforced Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$55.25

Beckson Thirsty-Mate 4' Intake Extension Hose f/124, 136 & 300 Pumps

0

Intake Extension HoseDesigned to extend the intake reach of the 124, 136 and 300 series pumps. Use the intake hose to pump out hard to see or reach areas. Comes with bilge strainer to prevent clogging. Makes difficult pumping jobs easier. Product : BECKSON THIRSTY-MATE 4' INTAKE EXTENSION HOSE F/..

$43.35

Beckson Thirsty-Mate 6' Intake Extension Hose f/124, 136 & 300 Pumps

0

Intake Extension HoseDesigned to extend the intake reach of the 124, 136 and 300 series pumps. Use the intake hose to pump out hard to see or reach areas. Comes with bilge strainer to prevent clogging. Makes difficult pumping jobs easier. Product : BECKSON THIRSTY-MATE 6' INTAKE EXTENSION HOSE F/ ..

$50.60

Beckson Thirsty-Mate Lifeboat & Commercial Vessel Pump - USCG Approved - 3' Inlet, 10' Outlet

0

Thirsty-Mate High Capacity Super PumpCoast Guard Approved for commercial useManufactured to exceed the original requirements of Coast Guard regulation No. 519C. The specifications of this regulation were later reduced when no hand pump other than Beckson's could pass the test requirements. Still "ov..

$439.00

Beckson Thirsty-Mate Pump 18L w/20 Flexible Reinforced Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$34.80

Beckson Thirsty-Mate Pump 30 w/32 Flexible Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$43.70

Beckson Thirsty-Mate Pump 36 w/36 Flexible Reinforced Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$51.20

Beckson Thirsty-Mate Pump 36 w/72 Flexible Reinforced Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$61.65

Beckson Thirsty-Mate Pump 36 w/9' Flexible Reinforced Hose

0

Thirsty-Mate Hand PumpThe Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve ..

$84.90

Showing 1 to 36 of 178 (5 Pages)